Renovations

Wrapping Posts and Beams with Pine Boards.

Hello folks. We are still here, just busy. I wanted to show you how we went about wrapping posts and beams in an older home.

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Neat right?

Lets go back to the beginning. Jim got a call from a homeowner who asked us go to his house about 35 minutes away, to see if it was possible to wrap two long and two short beams and two posts in wood. I believe it was an older schoolhouse converted into a home and they wanted to leave the beams exposed. I mean, why wouldn’t you!! I know I would.

With lots and lots and lots of measurements on hand, Jim worked out a plan of how many boards we would need and how wide and long they should be. The homeowner placed the order and we picked up the boards and brought them home to prepare them.

The boards were 14 and 16 feet long so first we had to build a drying rack in the workshop.

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Drying rack.

Then it was time for stain. The homeowner selected Dark Walnut by Minwax and wanted two coats applied. We used gloves and a cloth to wipe on the stain, making sure also to cover the two sides. It took both of us 16 hours to get the two coats applied with some tight maneuvering in the workshop. It then took several days to completely dry with a fan running.

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Check out these beauties!

Before we packed up the truck to head out, Jim assigned each board a letter…A, B, C etc according to his drawings. This helped immensely since there were four different lengths and two different widths of boards. We wanted the seams to land at the posts. Are you following me?

We had to pick a couple of non-rainy days for the install since we were doing the cutting outdoors.

We decided to tackle one of the long beams first. This one was pretty straightforward. That’s not to say it was easy. In an older building such as this, nothing was square or even. The ceiling included. But Jim is not one to give up so here was the first section installed. One board on either side of the beam and one underneath. And the seam landing on the post.

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Note how the boards wrap around the post. Fun times.

You can also see in the above picture how we had to use spacers. Sometimes with shims on top. Lots of shims. Jim made these shims on the sawmill for this purpose.

Then it was time to bring in another board. With each one we did a test fit, brought it out to be trimmed, another test fit, and more trimming when necessary.

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Another test fit.

At the end of the first day we had the whole beam and post covered. On the second day we tackled the harder of the two. This one ran into a set of stairs and the beam being made of five 2×10 boards laminated together, and along the length to reduced to four boards, none of which were square…or flush…or level…or plumb.

This is the before of the second beam and post.

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Beam and Post #2.

And here is the after…

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
See the stairs and the angles?

‘All in a day’s work’, as they say. This beam and post carried through to the second floor.

Before…

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Lots more angles and a little back cutting of the steps.

And after…

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Isn’t it pretty!!!

In case you thought we were done…nope. The beam by the stairs also ran into a wall and came out the other side.

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Drywall covering the beam.

We cut away the drywall in that section and continued the beam wrap all the way to the outside wall. That took care of the second day.

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
That’s better!

The first beam also continued through the wall and into the next room so we had to go back on the third day to finish up. This one was a shorter beam that didn’t take long to cover.

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Finishing touches.

We used glue and a nail gun for the install and even though the holes were tiny, with the wood stained so dark you could see every teeny tiny nail hole with the lighter wood from inside showing. I used a q-tip, the walnut stain and a cloth to touch up every nail hole. It did the trick and looked fantastic. I also ran a little stain down any seam to make sure no lighter wood showed. It was worth the effort.

Here is another quick shot of the two beams. Before…

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Looking naked.

After…

posts,beams,beam wraps,pine boards,carpentry,woodworking,staining
Fully dressed.

With the job complete, I’ve been looking around our house to see where beams could go, even if ours were fake. Who would know! Well probably all of you cause I would have to show you. Now I just need Jim to think it was his idea so he would be onboard.

Later.

Leave a Reply

Your email address will not be published. Required fields are marked *