Machinery,  Sawmill

Saw Mill Laser Installation

A laser beam allows a sawyer to see on the log where the blade will travel before starting the cut. This can be handy as it will save some time when cutting crooked logs or when you want specific features added to, or cut from, live edge slabs. Laser beam kits are available for many of the bigger, more expensive saw mills but for our small manual mill, no luck. Time to make up a DIY kit. Beam me up!

saw milling,laser lines,diy kits
laser line

I emailed a company and presented them the idea of what I wanted to achieve. They were very prompt with their email reply as well as professional and knowledgable. I had several questions and each answer brought new questions. We ended up emailing back and forth several times, to the point where they called me to expedite my inquiry. They were very helpful and accommodating, which I find to be a rare commodity in B2B relationships these days.

Their recommendation was a 10 mW laser module for the task. I wanted to be sure I could see the laser beam so I requested a 50 mW (largest one they had). I have no clue as to what may be needed so I figure bigger is better, right? They assured me 10 mW would be sufficient but left it up to me. I ordered the 50 mW. They then kindly offered their 10 mW and 20 mW laser modules to allow me to test the differences.  I’m the guy who can test a hammer and hit my thumb, so what could possibly go wrong with me testing laser beams?!?! 🙂

saw milling,laser lines,lights,laser beams,diy kits
laser line module parcel

The box arrived, professionally packed and included everything we had discussed.

saw milling,laser lines,lights,laser beams,diy kits
laser kit

Here is where I mounted the kit. I discovered that the electrical leads of the battery box could make contact with the aluminum housing of the sawmill, which can cause the laser module to not work. So either the battery box, or the mounting bracket, should be insulated from the aluminum housing.  The battery box and the laser are not weather proof. I will be placing a roof over the sawmill at some point in the future, but for now I will have to construct some sort of weather shield.

saw milling,laser lines,lights,laser beams,diy kits
mounting the laser line

My mill is outdoors, so I was already under the assumption that I would not see laser line under full sun. That turned out to be accurate for the 10 mW and the 20 mW modules. The 50 mW module was visible when clouds are present. There is no doubt that if the sawmill was under a shelter, this laser line using any of those powers would be more visible.

saw milling,laser lines,lights,laser beams,diy kits
5 pm outdoors

So I waited an hour. I figured that at 6 pm the lighting conditions would be similar to that of being under a roof shelter. The 50 mW laser did not disappoint, casting a easy to see beam of light.

saw milling,laser lines,lights,laser beams,diy kits
6pm easy to see

It not only cast a light on the log, but right across the work yard, easily reaching the embarkment more than 100 ft away.

saw milling,laser lines,lights,laser beams,diy kits
6pm laser line outdoors
saw milling,laser lines,diy kits
laser line
saw milling,laser lines,lights,laser beams,diy kits
6 pm 50 mW module
saw milling,laser lines,lights,laser beams,diy kits
6pm 50 mW module broadcasts beam
saw milling,laser lines,lights,laser beams,diy kits
beam travels far across the work yard

Its quickly starting to turn dusk so I took out the 50 mW module and placed the 20 mW module in its place. The results were impressively similar.

saw milling,laser lines,lights,laser beams,diy kits
20 mW shows just as well

To my surprise, even the 10 mW module broadcast a line that was easily viewable.

saw milling,laser lines,lights,laser beams,diy kits
10 mW very clear too

All that is left to do now is field testing. That is, to run the saw and cut some logs, to see how the laser module, mounting bracket and battery box endures the harsh environment (vibrations and dust) of the sawmill. Check back again for more results.

Update December 2018

I have used the laser a couple times this year. I have not sawed much this past summer so I haven’t used it much. For the few times i have used it, its worked well. The mount keeps its position pretty good. The head of my saw doesn’t vibrate much. Usually about 10 logs or so I might have to readjust the laser line. Keep in mind the purpose of the laser for me is to estimate blade position across the log when dealing with  heavy tapered logs or odd shaped logs.

Some people have inquired about where I got the kits. I bought them from Apinex, located in Quebec Canada. They sell direct. Comment below if you have a question or comment.

A Newfoundland born Canadian with a life long interest in woodworking, baking and anything else that peaks my curiosity.

4 Comments

Leave a Reply

Your email address will not be published. Required fields are marked *